Dwin HD-700 Provozní pokyny

HD-700 SUPERDATAPROJECTION MONITORInstallation and Operating InstructionsRead these instructions completely before operating this unit.Contents subjec

- 10 -Remote Control OperationThe HD-700 has no on board user controls. All operation is controlled through the wireless remote control or theoptional

- 11 -Initial Set Up and AdjustmentAt this point you are ready to proceed with the initial adjustment of the unit. Make certain that the power andsign

- 12 -Press “1” to view the focus screen. Note that the screen willdisplay the Focus menu against a background of the focuspattern.Signal LevelBefore

- 13 -Geometry Adjust MenuGeometry is the series of adjustments that correctly align the picture scans to the size of the screen. Just asimportant, g

- 14 -1. SizePress “1” to select “Size” adjustmentAdjust the height and width by using the / / / arrow buttons to fill the proper aspect ratio fory

- 15 -RED GEOMETRYThe adjustments for Red Geometry are similar to those usedto set the Green Geometry, except that instead of using thescreen as a phy

- 16 -Convergence AdjustmentsOnce the picture has been focused and adjusted to the screen size for all geometry parameters, the nextstep in the set up

- 17 -Convergence MovementDuring convergence there are two modes: cursor movement and circuit adjustment. When you start theconvergence process the

- 18 -Convergence Memory PurgeDuring some adjustments, particularly after other service adjustments, you may need to purge, or “dump” thecomplete memo

- 19 -Gray Scale AdjustmentThe HD-700 offers a wide range of gray scale adjustments. For best results we recommend first using theinternal test signal

- 2 -Table of ContentsSafety Information ___________3Important Information for the User___________________4Specifications

- 20 -Brightness AdjustmentThe brightness setting should be adjusted so that the on screen video maintains proper contrast. The pictureshould be adjus

- 21 -Centering AdjustmentsThese adjustments permit you to properly center the picture to the screen. They will not impact geometry orconvergence sett

- 22 -Size AdjustmentsThe size adjustments are the final picture adjustment. They define the size of the picture within the blankingarea previously

- 23 -Once the unit is delivered to an end user you may wish to lock out most of the major adjustment settings.This will limit the amount of adjustmen

- 24 -Source Memory Copy, Rename or DeleteThis will enable you to copy, rename or delete memory occupied by Source Configuration data.To copy, rename

- 25 -Default MemoryThe HD-700 is programmed with a default memory. This is a 'base" memory that will maintain, geometry,convergence and gr

- 26 -Table 1Connector Settings Horizontal VerticalFront Floor H2 V2Front Ceiling H1 V1Rear Floor H1 V2Rear Ceiling

- 27 -Screen Size Change ProceduresThe HD-700 is delivered from the factory with settings for a 100” diagonal screen and a 4:3 aspect ratio. Theunit i

- 28 -HD-700 projector’s RS232 ControlThe RS232 interface for HD-700 can be operated from any terminal, such as a Windows 95, 98PC running HyperTermin

- 29 -Limited WarrantyThis warranty applies only to the first person or entity that purchases the HD-700 for personal orbusiness use and not for the p

- 3 -SAFETY INFORMATION1. Read and apply all of the safety and operating instructions provided with your videoequipment.2. Keep all safety and

- 4 -the original part. Unauthorized substitutions may result in fire, electric shock, or otherhazards.17. Upon completion of any service or re

- 5 -DWIN HD-700 DATA PROJECTION MONITORSPECIFICATIONS AND TECHNICAL DATASystem Description: Three CRT/three lens refractive projection system for li

- 6 -IntroductionThis manual contains the information required to properly install, configure, setup and operate the DWINHD-700 superdata projection

- 7 -Pre Installation PreparationsPlanning a projection television installation is a critical part of the installation. Even with the extended rangeof

- 8 -Front Panel ConnectionsMake the appropriate connections to the front panel, using the following descriptions as a guide.DWINHD-7001

- 9 -Preparation for AdjustmentBefore initial adjustments are made to the unit, locate the correct distance from thescreen. This distance should be ob